1985 Tayana 42 Center Cockpit $135,000.00

S/V Running Free Specifications

Tayana V42 Hull #101
General Construction

Hand laminated fiberglass construction with mat and unidirectional woven roving, vinylester resin for first five layers to prevent blistering.

Internal iron ballast glassed into a modified fin keel with choice of drafts.

Skeg mounted rudder, with internal stainless steel rudder post and integral stainless steel reinforcement.

The deck is a composite construction using end grain light wood coring.

All deck hardware areas are reinforced using encapsulated marine grade plywood.

Deck hardware is through bolted using stainless steel backing plates.

Standard Hardware and Equipment

Engine and Steering

Perking 4 cylinder 4.108 51 B.H.P. marine diesel engine.

Flexible engine mounts.

Engine alarm systems.

Leadfree foam insulated engine compartment.

Raw water strainer for engine intake.

Antisyphon valve.

Muffler/ waterlock system.

Shaft strut with cutlass bearing.

Stainless steel prop shaft with three-blade bronze Maxi propeller.

Strong dripless shaff seal
Three black iron fuel tanks, capacity 140 gal.

Steering pedestal with dual lever controls.

Stainless steel "destroyer" type steering wheel.

Emergency steering system with tiller.

Rudder bearing.

Bronze rudder shoe for skeg mounted rudder.

Flemming Self sterring system.

Spars and Rigging

Double spreader aluminum mast and boom.

Four halyards; main, genoa, spinnker w/ATN and staysail.

Internally led topping lift and outhaul.

Anchor light and masthead tricolor.

Combination deck and steaming light.

Masthead mounted windex.
1 X 19 stainless steel standing rigging with Swedged ends.


Customized electrical panels.

D/C panel section includes master breaker for load groups.

Full gauges for AC and DC panels.
110 volt shore power system – 30 AMP
110 volt outlets.
110 volt GFI outlets in heads.

Two 12-volt marine H.D. 120 AGM batteries in FRP boxes.

Heavy duty battery selector switch – 3 position.
40 AMP – Freedom 25 inverter/battery charger w/Links 2000R.

Internal bonding system to all chain plates, thru hulls, engine and rudder system.

Zincs as required.

Numerous overhead cabin lights designed to interior lighting plan.

Engine room blower.

Chart table light.

Running lights to international rule.

Sails and Canvas

Neil Pryde Mainsail with 3 Reef Points with Dutchman flaking system and cover.

Neil Pryde Cruise Plus Yankee on Profurl with bag.

Neil Pryde Cruise Plus Staysail Jib with bag.

Neil Pryde Cruising Spinnaker.

Trysail on separate mast track.

Stormsail, staysail mounted

Deck Fittings

Non-skid side decks and cabin house top.

Aluminum toe rail.

Six custom stainless steel mooring fairleads.

Four yachtsman type 12" stainless steel mooring cleats, stern samson post
Stainless steel bow and stern pulpits.

Stainless steel stanchions.

Stainless steel boarding gates port and starboard.

Double life lines.

Stainless steel cockpit drains.

Stainless steel mast guards.

Four FRP dorade vents with custom teak dorade boxes.

Two stainless steel deck mounted pad eyes.

Lewmar or equivalent, aluminum overhead hatches.

Stainless steel opening ports with safety glass.

Custom stainless steel fixed windows with safety glass (center cockpit).

Aluminum genoa and staysail tracks with cars.

Traveler system with control lines and hardware.

Deck organizers.

Sheet stoppers.

All required blocks for sheets and halyards.

Teak cockpit sole and seats.

Fiberglass molded propane storage compartment for two tanks.

Two molded coaming compartments.

Teak companionway doors.

Teak companionway drop boards.

All winches are Lewmar Self Tailing.
2 – Lewmar #43 CST primary winches.
2 – Lewmar #40 CST secondary winches.
1 – Lewmar #10 main halyard winch.
1 – Lewmar #10 jib halyard winch.
1 – Lewmar #7 staysail halyard winch.
1 – Lewmar #7 reef winch.

Winch handles.

Center Cockpit:

Two stainless steel water tanks with baffles, total capacity 150 gal.

Ten gallon hot water heater (110 volt and engine heat exchanger).

Hot and cold pressure water system.

Self priming fresh water pump.

Accumulator tank.

Pressure water system with faucets in galley and head.

Large stainless steel double sink in galley.

Large heads with shower.

Sumps pump for shower.

Oval stainless steel sink in heads.

Manual toilets in heads.
35 gal.

Holding tank and piping for waste disposal in head.

Bronze ball cocks/thru hull fittings bonded to shops systems.

Electric 12 volt bilge pumps with automatic float switch.

Manual bilge pump.


Custom stainless steel double bow roller/stern head fittings.
45 Lb.

CQR Plow anchor, 66# Bruce with 300'chain and rode.

One 50 Danforth, one Frotress and one 65# Luke.

Two speed manual windlass.

Standard one staterooms, two head layout.All bulkheads of marine grade plywood with compression fillets against hull sides.

Teak veneer and solid teak trim on all interior bulkheads and cabinetry.

Solid teak beveled cabin doors with louvers.

Solid teak louvered doors on all lockers.

Custom teak navigation station with custom seating.

Teak dinette table.

Spruce ceilings on exposed hull sides.

Teak handrails, port and starboard.

Removable vinyl overhead with teak battens.

Solid teak and holly cabin sole.

Numerous removable floor boards with stainless steel hardware.

Formica counter tops in galley and heads with stainless steel sinks.

Hand rubbed satin varnish on all interior teak surfaces.
4" deluxe cushions covered in choice of fabric.


4" foam insulated refrigerator and freezer compartments, lined in stainless steel.

Three burner stainless steel propane stove with oven.

Stainless steel lined stove area.

Two propane tanks.

Custom deep double stainless steel sinks.

Formica counter tops.

Trash bin.

Numerous drawers, lockers and dry storage bins.

Complete Coast Guard Equipment Package including: PFD